Description

Fit For: 2003-2006 KIA SORENTO All Models Package Includes: 1x Front Right Upper Control Arm - K80342 1x Front Left Upper Control Arm - K80343 Fault judgment: When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted. When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving. 2Pcs Front Control Arms Kit For 2003-2006 Kia Sorento 3.5L Fits K80342 K80343 Fit For: 2003-2006 KIA SORENTO All Models Package Includes: 1x Front Right Upper Control Arm - K80342 1x Front Left Upper Control Arm - K80343 Fault judgment: When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted. When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving. A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose. Know how to replace the ball joint: step 1: Getting Started Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove. After the tire screws are loosened, jack up the jack. At this time, completely remove the wheel nut, and then remove the tire from the vehicle. step 2: Removing the Old Ball Joint Pop loose the ball joint. You will most likely need to use a hammer and a special tool called a “pickle fork” or tie rod separator to get enough leverage to maneuver. With the wrench, remove the largest nut from the joint, replace with the new nut, and then drive the pickle fork between the control arm and the steering knuckle. And before hammering away,you will need to put the castellated nut on. Remove the allen bolts and slide the control arm free. Loosen bolts or drill out rivets holding the ball joint in place, and slide out the ball joint. step 3: Installing the New Joint Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. Bolt the joint into place using the hardware included. Torque the bolts to the proper specifications.Generally, the specs will be about 44 pounds per foot on the screws and around 80 for other bolts. Always defer to the owner's manual for accurate numbers, however. Screw in the new grease fitting and pump grease into the assembly. Notes: Please be sure to check carefully whether the part is suitable for your car model before placing an order. If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer. Item Specifics Brand everpartstorecs Placement on Vehicle Left Manufacturer Part Number 10299270 Interchange Part Number K80342,K80343 Superseded Part Number Front Driver And Passenger Side Replacement Vintage Car Part No Type Control Arm & Ball Joint Assembly Manufacturer Warranty 1 Year Material Alloy Steel Items Included Mounting Hardware Mounting Style Bolt-On Universal Fitment No Cotter Pin Hole Yes Adjustable Yes Modified Item Yes Custom Bundle Yes OE Spec or Performance/Custom OE Spec Control Arm Construction Forged Features Greasable Kit or Single Part Kit Kit Included 2 Pcs Finish Coated Surface Finish Polished, Rust Protected Partslink-number control arms,For Sorento Kia Store Speciality Suspension & Steering Suspension Grade Standard OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly Kit Parts Included Control Arm, Ball Joint Shipping 1.We will ship your order within 2 working days after confirming the payment, and most areas will receive delivery within 2-8 working days. 2.All orders will be shipped from our US warehouses and delivered by USPS , UPS or FedEx. 3.We will deliver the product to the address filled in eBay, if you need to change your address, please make sure you tell us the new address within 12 hours after payment (no delivery to remote areas). 4.We will provide you with a logistics tracking number, you can check the logistics status according to the number in time, if there are any problems, contact us immediately please . Payment PayPal preferred. Other payments accepted by ebay also can be accepted. Service 1. Products can be returned for no reason within 30 days of receipt (products to be returned must be in a resalable condition, if they have been used we will not accept the return). 2. If the product does not match the description on the product page, we will exchange or refund the product for free within 30 days. 3. We offer one year warranty, but man-made damage by abuse or wrong operation is not covered by this warranty. Note If you have any concerns about the product or before providing a review or feedback, please contact us immediately, we will give a satisfied solution. Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items. STORE HOME HOT SELLING COOL SUMMER SENSORS EXTERIOR Shop Category Store Home lift support Condenser Air Diesel Heater Blower Resistor Blower Motor Heater Core Suspension Kits Thermostat Housing ABS Wheel Speed Sensor Window Switch Oxygen Sensor 3Rd Brake Light Mass air flow sensor AC Compressor Cooling Fan Towing Mirrors Door Handle Roof Rack Radiator Sensor Knock Sensor Catalytic Converter Window Regulator Wheel Spacers Other 2Pcs Front Control Arms Kit For 2003-2006 Kia Sorento 3.5L Fits K80342 K80343 Fit For: 2003-2006 KIA SORENTO All Models Package Includes: 1x Front Right Upper Control Arm - K80342 1x Front Left Upper Control Arm - K80343 Fault judgment: When encountering a limp road, the vibration is strong, and it is shaking up and down, and the body is twisted. When the car is driving, every time it vibrates up and down, the suspension device makes a "guckling" noise If there is a problem with the front wheel suspension system, the direction will deviate to one side, and continuous correction is required to maintain normal driving. A normal shock absorber will generate heat when it is working. If it does not generate heat or if oil leaks from the shock absorber, it means that the shock absorber has been damaged. During the inspection, the condition of the shock absorber rubber sleeve should also be checked. If it is found to be damaged, it should be replaced together with the shock absorber in time. In addition, it may be that the fastening bolts are loose. Know how to replace the ball joint: step 1: Getting Started Engage the parking brake. Set the parking brake on the vehicle and set the wheel block on one of the tires you will not remove. After the tire screws are loosened, jack up the jack. At this time, completely remove the wheel nut, and then remove the tire from the vehicle. step 2: Removing the Old Ball Joint Pop loose the ball joint. You will most likely need to use a hammer and a special tool called a “pickle fork” or tie rod separator to get enough leverage to maneuver. With the wrench, remove the largest nut from the joint, replace with the new nut, and then drive the pickle fork between the control arm and the steering knuckle. And before hammering away,you will need to put the castellated nut on. Remove the allen bolts and slide the control arm free. Loosen bolts or drill out rivets holding the ball joint in place, and slide out the ball joint. step 3: Installing the New Joint Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. Bolt the joint into place using the hardware included. Torque the bolts to the proper specifications.Generally, the specs will be about 44 pounds per foot on the screws and around 80 for other bolts. Always defer to the owner's manual for accurate numbers, however. Screw in the new grease fitting and pump grease into the assembly. Notes: Please be sure to check carefully whether the part is suitable for your car model before placing an order. If you have any questions after receiving the goods, please contact us in time, we will give you a satisfactory answer. Shipping Payment Service Note 1.We will ship your order within 2 working days after confirming the payment, and most areas will receive delivery within 2-8 working days. 2.All orders will be shipped from our US warehouses and delivered by USPS , UPS or FedEx. 3.We will deliver the product to the address filled in eBay, if you need to change your address, please make sure you tell us the new address within 12 hours after payment (no delivery to remote areas). 4.We will provide you with a logistics tracking number, you can check the logistics status according to the number in time, if there are any problems, contact us immediately please . PayPal preferred. Other payments accepted by ebay also can be accepted. 1. Products can be returned for no reason within 30 days of receipt (products to be returned must be in a resalable condition, if they have been used we will not accept the return). 2. If the product does not match the description on the product page, we will exchange or refund the product for free within 30 days. 3. We offer one year warranty, but man-made damage by abuse or wrong operation is not covered by this warranty. If you have any concerns about the product or before providing a review or feedback, please contact us immediately, we will give a satisfied solution. Do check the compatible chart or contact us if you have any quetion in compatibilities before ordering the items.